|
User's Guides
|
|
Written by BestBuyLCD.com
|
|
Tuesday, 21 April 2009 13:55 |
|
Page 2 of 2 INSTALLATION
Connecting a VCR
These instructions assume that you have already connected your TV to an antenna or
a
cable TV system (according to the instructions on pages 6-9)
.
Skip step 1 if you have not yet connected to an antenna or a cable system.
1
Unplug the cable or
antenna from the
back of the TV.
2
Connect the cable or
antenna to the ANT IN VCR Rear Panel
terminal on the back of
the VCR.
Incoming Cable
or Antenna
3
Connect an RF cable
TV Rear Panel
between the ANT OUT
terminal on the VCR
and the ANT IN
VCR Rear Panel
terminal on the TV.
RF Cable <Optional>
An RF cable is usually included with a VCR. (If not, check your local electronics store).
4
Connect an audio cable
between the AUDIO OUT
TV Rear Panel
Audio Cable <Optional>
VCR Rear Panel
jacks on the VCR and
the AV IN [L-AUDIO-R]
jacks on the TV.
If you have a “mono” (non-stereo) VCR, use the Y-connector (not supplied) to hook up to the left
and right audio input jacks of the TV.
English-6
01 BN68-00816A-00.qxd 2/1/05 4:14 PM Page 11
INSTALLATION
5
Connect a video cable
between the
VIDEO OUT jack on the
VCR and the AV IN
[VIDEO] jack on the TV.
TV Rear Panel
Video Cable <Optional>
VCR Rear Panel
Follow the instructions in “Viewing a VCR or Camcorder Tape” to view your VCR tape.
* Each external input source device has a different back panel configuration.
Connecting an S-VHS VCR
Your Samsung TV can be connected to an S-Video signal from an S-VHS VCR.
(This connection delivers a better picture as compared to a standard VHS VCR.)
1
To begin, follow steps
1–3 in the previous
TV Rear Panel
section to connect the
antenna or cable to
VCR Rear Panel
your VCR and your TV.
RF Cable <Optional>
An RF cable is usually included with a VCR. (If not, check your local electronics store).
2
Connect an audio cable
TV Rear Panel
between the AUDIO
OUT jacks on the VCR
and the AV IN
[L-AUDIO-R] jacks on
the TV.
VCR Rear Panel
Audio Cable <Optional>
English-7
01 BN68-00816A-00.qxd 2/1/05 4:14 PM Page 12
INSTALLATION
3
Connect an S-Video
TV Rear Panel
cable between the
S-VIDEO OUT jack on
the VCR and the
S-VIDEO IN jack on the
TV.
VCR Rear Panel
S-Video Cable <Optional>
An S-video cable is usually included with an S-VHS VCR.
(If not, check your local electronics store.)
* Each external input source device has a different back panel configuration.
Connecting a DVD Player
The rear panel jacks on your TV make it easy to connect a DVD player to your TV.
1
Connect an audio cable
between the TV Rear Panel
COMPONENT IN
[L-AUDIO-R] jacks on
DVD Player Rear Panel
the TV and the AUDIO
OUT jacks on the DVD
player.
Audio Cable <Optional>
2
Connect a component
cable between the
COMPONENT IN
[Y, PB, PR] jacks on the
TV and the
COMPONENT
[Y, PB, PR] jacks on
the DVD player.
TV Rear Panel
Component Cable <Optional>
DVD Player Rear Panel
Note : For an explanation of Component video, see your DVD player owner's manual.
The component terminal of this set only supports 480i/480p resolution.
* Each external input source device has a different back panel configuration.
English-8
APPENDIX
English-9
Retractable Stand
Note: The maximum tilt angle is 13 degrees in the backward direction.
Please do not tilt the TV outside the specified range. Using excessive force
to tilt the TV may cause permanent damage to the mechanical part of the stand.
04 BN68-00816A-00.qxd 2/1/05 4:21 PM Page 57
04 BN68-00816A-00.qxd 2/1/05 4:21 PM Page 5
8
APPENDIX
Installing VESA compliant mounting devices
Mounting pad
<1>
<2>
<1> Fold the stand pressing the button on the back of the stand.
<2> Align the mounting interface pad with the holes in the stand bottom and secure it with the four
screws that come with the arm-type base, wall mount hanger or other bases.
Wall Mount Instructions
The following instructions apply to a hollow sheet-rock wall only. Tools/Hardware needed - Philips
screwdriver, four toggle bolts, 5/8in dia. Drill bit and drill. Contact Ergotron at (800) 888-8458 to
purchase the triple pivot direct mount adapter and wall mount bracket kit.
• LN-R1550 (15")
:
No. 47 - 007 - 099 (Pivot direct mount adapter)
No. 97 - 101 - 003 (Wall mount bracket kit)
• LN-R2050 (20")
:
No. 47 - 007 - 099 (Pivot direct mount adapter)
No. 97 - 101 - 003 (Wall mount bracket kit)
Align the wall mount bracket on the wall at the desired height, making sure that the bracket will be
mounted between the wall studs. Mark the four corner openings and drill four 5/8-diameter holes.
Assemble the wall mount kit according to the instructions provided with it. Securely attach Ergotron’s
flat panel, triple pivot direct mount adapter to the back of the TV using the four 4mm,
0.7 pitch x 10mm screws provided with the arm. Secure the assembly to the wall using four 3/16 by
3-inch long toggle bolts.
English-10
English-11
APPENDIX
Installing the Wall Mount Kit
Note : This installation is to be used when attaching the wall mount to a concrete wall.
When attaching to other building materials, please contact your nearest dealer.
Components
Please use provided components or parts to install the Wall Mount Kit.
Mark the location of hole on the wall using installation guide.
Make over 35mm- depth- hole on the marked location using
5.0-diameter drill.
Fix anchors on each hole on the wall.
Connect bracket to the wall with screws after fitting anchors
into the bracket holes.
Note : If the bracket is not firmly fixed to the wall, LCD TV can fall off.
How to assemble the Wall Mount Kit
Bracket Anchors : 3EA Screws : 3EA Installation Guide
You may use LCD TV right after fixing it to the wall since stand is
wrapped already turned over as shown in the picture below.
2
1
When using LCD TV in stand-based form, place the product on a
cushion or other soft materials. Then turn over stand following the
arrow direction below only after pressing button on the connected
part where LCD TV is attached to stand.
(Turn over stand in the opposite direction after pressing button when
using LCD TV in wall-mounted form as well.)
3
04 BN68-00816A-00.qxd 2/1/05 4:21 PM Page 59
English-12
Installing the Wall Mount Kit
APPENDIX
How to adjust an angle
When bracket is assembled on the wall How to hang monitor up on a hook When installation is completed
(1) Angle adjustment section of
general stand-besd LCD TV
(2) Angle abjustment section
while converting the form
(1->3, 3->1)
(3) Angle adjustment section of
wall-mounted LCD TV
Adjust LCD TV to the hook on the bracket and move in the direction of the arrow(Left) so that LCD TV can be completely
fixed to the bracket.
4
5 Remove Installation Guide after completing setup of LCD TV on the wall.
Push the LCD TV up and shift to the right to detach it from bracket.
When moving or transferring to other areas, reverse No. 4 procedure so as to disconnect LCD TV with ease.
6
Picture (1) shows the adjustment angle (0°~ 13°) when you use LCD TV in its general form (stand-based
LCD TV).
Excessive tilting can turn LCD TV over which might cause damage to LCD TV.
Picture (2) shows the adjustment angle (13°~ 80°) when you convert stand-based LCD TV into wall-mounted
one.
Picture (3) shows the adjustment angle (0°~ 10°) when you use wall-mounted LCD TV after fixing it to wall.
Note : Picture (2) shows the angle adjustment section while LCD TV is being converted from stand-based
one to wall-mounted one or vice versa.
- Click" sound indicates section change from 1 to 2 or 3 to 2 (1->2, 3->2).
04 BN68-00816A-00.qxd 2/1/05 4:21 PM Page 60
Quote this article on your site
To create link towards this article on your website,
copy and paste the text below in your page.
|
