Buy LCD
 
TV or not TV?
Home

Bookmark this Page

 

RSS FEED

BestBuyLCD BestBuyLCD

SAMSUNG LTN325W

User Rating: / 4
PoorBest 
Written by BestBuyLCD.com   
Tuesday, 21 April 2009 23:00
Article Index
SAMSUNG LTN325W
Page #
All Pages
Owner’s Instructions
LCD TV with Life-Like Picture & Sleek Design LTN325W I LTN406W
BN68-00448A-00
Owner’s Instructions
LCD TV with Life-Like Picture & Sleek Design LTN325W I LTN406W
BN68-00448A-00

 venus-01-en 6/4/03 2:42 PM Page 2



Important
Safety Instructions

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings, Install in accordance with the manufacturer’s
instructions.

8) Do not install near any heat sources such as radiators, heat registers, or other apparatus
(including amplifiers) that produce heat.

9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug
has two blades with one wider than the other. A grounding type plug has two blades and a
third grounding prong. The wide blade or the third prong are provided for your safety.
If the provided plug does not fit into your outlet, consult an elec trician for replacement of
the obsolete outlet.

10) Protect the power cord from being walked on or pinched particu
larly at plugs, convenience receptacles, and the point where they
exit from the apparatus.

11) Only use attachments/accessories specified by the manufacturer.

12) Use only with cart, stand, tripod, bracket, or table specified by
the manufacturer, or sold with the apparatus. When a used, cau
tion when moving the cart/apparatus combination to avoid injury
from tip-over.


13) Unplug this apparatus during lightning storms or when unused
for long periods of time.

14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus
has been damaged in any way, such as power-supply cord or plug is damaged, liquid has
been spilled or objects have fallen into the apparatus, the apparatus has been exposed
to rain or moisture, does not operate normally, or has been dropped.

1 SAFETY



 venus-01-en 6/4/03 2:42 PM Page 3



CAUTION This symbol indicates high voltage is
of this product.
CAUTION: TO REDUCE THE RISK OF ELEC

This symbol alerts you that important

TRIC SHOCK, DO NOT REMOVE COVER

literature concerning operation and

(OR BACK). NO USER SERVICEABLE PARTS

maintenance has been included with this

INSIDE. REFER SERVICING TO QUALIFIED

product.

SERVICE PERSONNEL.


Note to CATV system installer: This reminder is provided to call CATV system
installer’s attention to Article 820-40 of the National Electrical Code (Section 54 of
Canadian Electrical Code, Part I), that provides guidelines for proper grounding and,
in particular, specifies that the cable ground shall be connected to the grounding
system of the building as close to the point of cable entry as practical.

Caution: FCC/CSA regulations state that any unauthorized changes or modifications
to this equipment may void the user’s authority to operate it.

Caution: To prevent electric shock, match the wide blade of plug to the wide slot, and
fully insert the plug.

Attention: pour eviter les chocs electriques, introduire la lame le plus large de la
fiche dans la borne correspondante de la prise et pousser jusqu’au fond.

Important: One Federal Court has held that unauthorized recording of

copyrighted TV programs is an infringement of U.S. copyright laws.
Certain Canadian programs may also be copyrighted and any unauthorized recording
in whole or in part may be in violation of these rights.

To prevent damage which may result in fire or electric shock
hazard, do not expose this appliance to rain or moisture.


As an ENERGY STAR Partner.
Samsung Electronics America, Inc. has determined that this product or product
model meets the ENERGY STAR guidelines for energy efficiency.



SAFETY 2


 venus-01-en 6/4/03 2:42 PM Page 4



FCC Information

User Instructions

The Federal Communications Commission Radio
Frequency Interference Statement includes the
following warning:
NOTE: This equipment has been tested and found
to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference in a residential
installation. This equipment generates,
uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the
instructions, may cause harmful interference to
radio communications. However, there is no guarantee
that interference will not occur in a particular
installation.

If this equipment does cause harmful interference
to radio or television receptions, which can be
determined by turning the equipment off and on,
the user is encouraged to try to correct the interference
by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the
equipment and receiver.
• Connect the equipment into an outlet on a
circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced
radio/TV technician for help.
User Information

Changes or modifications not expressly approved
by the party responsible for compliance could
void the user’s authority to operate the equipment.
If necessary, consult your dealer or an experienced
radio/television technician for additional
suggestions. You may find the booklet called How
to Identify and Resolve Radio/TV Interference
Problems helpful. This booklet was prepared by
the Federal Communications Commission. It is
available from the U.S. Government Printing
Office, Washington, DC 20402, Stock Number
004-000-00345-4.

The party responsible for product compliance:
SAMSUNG ELECTRONICS CO., LTD
America QA Lab of Samsung
3351 Michelson Drive,
Suite #290, Irvine, CA92612 USA

Warning

User must use shielded signal interface cables to
maintain FCC compliance for the product.
Provided with this monitor is a detachable power
supply cord with IEC320 style terminations.
It may be suitable for connection to any UL Listed
personal computer with similar configuration.
Before making the connection, make sure the voltage
rating of the computer convenience outlet is
the same as the monitor and that the ampere rating
of the computer convenience outlet is equal to
or exceeds the monitor voltage rating.
For 120 Volt applications, use only UL Listed
detachable power cord with NEMA configuration
5-15P type (parallel blades) plug cap. For 240 Volt
applications use only UL Listed Detachable power
supply cord with NEMA configuration 6015P type
(tandem blades) plug cap.

IC Compliance Notice

This Class B digital apparatus meets all requirements
of the Canadian nterference-Causing
Equipment Regulations of ICES-003.
Cet appareil Numérique de classe B respecte
toutes les exigences du Règlemont NMB-03 sur
les équipements produisant des interférences au
Canada.

Notice de Conformité IC

Cet appareil numérique de classe B respecte
toutes les exigences du Règlement ICES-003 sur
les équipements produisant des interférences au
Canada.

VCCI

This is a Class B product based on the standard
of the Voluntary Control Council for Interference
by Information Technology Equipment (VCCI). If
this is used near a radio or television receiver in a
domestic environment, it may cause radio interference.
Install and use the equipment according to
the instruction manual.

This Class B digital apparatus complies with
Canadian ICES-003. Cet appareil numéique de la
classe B estconforme à la norme NMB-003 du
Canada.


This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause unesired operation.
This television receiver provides display of television closed captioning in accordance with §15.119 of the FCC rules.
3 SAFETY



 venus-01-en 6/4/03 2:42 PM Page 5



Important Warranty Information
Regarding Television Format
Viewing

Standard screen format televisions (4:3, the aspect ratio of the screen width to height) are primarily
designed to view standard format full-motion video. The images displayed on them should primarily
be in the standard 4:3 ratio format and constantly moving.
Displaying stationary graphics and images on screen, such as the dark top and bottom letterbox bars
(wide screen pictures), should be limited to no more than 15% of the total television viewing per week.


Wide screen format televisions (16:9, the aspect ratio of the screen width to height) are primarily
designed to view wide screen format full-motion video. The images displayed on them should primarily
be in the wide screen 16:9 ratio format, or expanded to fill the screen if your model offers this feature,
and constantly moving. Displaying stationary graphics and images on screen, such as the dark
side-bars on non-expanded standard format television video and programming, should be limited to
no more than 15% of the total television viewing per week.


Additionally, viewing other stationary images and text such as stock market reports, video game
displays, station logos, web sites or computer graphics and patterns, should be limited as described
above for all televisions. Displaying any stationary images that exceed the above guidelines can
cause uneven aging of picture tubes (LCDs) that leave subtle, but permanent burned-in ghost images
in the television picture. To avoid this, vary the programming and images, and primarily display full
screen moving images, not stationary patterns or dark bars. On television models that offer picture
sizing features, use these controls to view the different formats as a full screen picture.


Be careful in the selection and duration of television formats used for viewing. Uneven LCD aging
as a result of format selection and use, as well as other burned-in images, is not covered by your
Samsung limited warranty.


[Note]
If a still image is displayed for an extended period of time, residual images or blurring may appear.
When you need to leave the monitor unused for an extended period of time, adjust the settings so


that the monitor automatically goes into energy saving mode or activates the screen saver to display
moving images.



SAFETY 4


 venus-01-en 6/3/03 3:02 PM Page 4



Operation

CONTENTS


Chapter 1: Your New TV . . . . . . . . . . . . . . . .1

List of Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
List of Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Familiarizing Yourself with Your New TV . . . . . . . . . . . . . . . . . . . . . . .2
Front Panel Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Rear Panel Jacks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Installing Batteries in the Remote Control . . . . . . . . . . . . . . . .6

Chapter 2: Installation . . . . . . . . . . . . . . . . . .7

Connecting VHF and UHF Antennas . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Antennas with 300-ohm Flat Twin Leads . . . . . . . . . . . . . . . . .7
Antennas with 75-ohm Round Leads . . . . . . . . . . . . . . . . . . . .8
Separate VHF and UHF Antennas . . . . . . . . . . . . . . . . . . . . . .8
Connecting Cable TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Cable without a Cable Box . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Connecting to a Cable Box that Descrambles All Channels . . .9
Connecting to a Cable Box that
Descrambles Some Channels . . . . . . . . . . . . . . . . . . . . . . . . . .9
Connecting a VCR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Connecting an S-VHS VCR . . . . . . . . . . . . . . . . . . . . . . . . . .12
Connecting a DVD Player . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Connecting a Digital TVSet-Top Box . . . . . . . . . . . . . . . . . . . . . . . . .13
Connecting the Speakers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Connecting a PC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Chapter 3: Special Features . . . . . . . . . . . .16

Turning the TVOn and Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Changing Channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Using the Channel Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Using the Pre-CH Button to select the Previous Channel . . .16
Adjusting the Volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Using Mute . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Viewing the Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Viewing the Menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Setting Up Your Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Chapter 4: Operation . . . . . . . . . . . . . . . . . .22

Plug & Play Feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Memorizing the Channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Selecting the Video Signal-source . . . . . . . . . . . . . . . . . . . . .23
Storing Channels in Memory (Automatic Method) . . . . . . . .24
Adding and Erasing Channels (Manual Method) . . . . . . . . . .25
To Select TV/Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
To Edit the Input Source Name . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
Using Automatic Picture Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Customizing the Picture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
Using Automatic Sound Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
Customizing the Sound . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
Selecting a Menu Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
Setting the Blue Screen Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
To Select an External Input Device . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
LNA(Low Noise Amplifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
Fine Tuning Channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35


1 CONTENTS



 venus-01-en 6/3/03 3:02 PM Page 5



CONTENTS


Viewing Picture-in-Picture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
Activating Picture-in-Picture . . . . . . . . . . . . . . . . . . . . . . . . .36
Selecting a Signal Source (External A/V) for PIP . . . . . . . . .37
Swapping the Contents of the PIP and Main image . . . . . . . .37
Changing the PIPChannel . . . . . . . . . . . . . . . . . . . . . . . . . . .37
Changing the Location of the PIPWindow . . . . . . . . . . . . . .37
Changing the Size of the PIPWindow . . . . . . . . . . . . . . . . . .37
Changing the Screen Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
Freezing the Picture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
Adjusting the Background Color . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
Setting the DNIe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
To Enjoy Dolby Digital Sound . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
Turning the Dolby ProLogic II On . . . . . . . . . . . . . . . . . . . .41
Turning the Dynamic Range On . . . . . . . . . . . . . . . . . . . . . .42
Speaker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
Time Delay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
TRADEMARK & LAVEL LICENSE NOTICE . . . . . . . . . .46
Ideal Speaker Placement . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46
Changing the STEREO Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
Selecting the Sound . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48
To Select an External Output Device . . . . . . . . . . . . . . . . . . . . . . . . . .49
Adjusting the Headphone Sound . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50
Setting the Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51
Setting the On/Off Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52
Setting the Sleep Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54
Using the V-Chip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55
Setting Up Your Personal ID Number (PIN) . . . . . . . . . . . . .55
How to Enable/Disable the V-Chip . . . . . . . . . . . . . . . . . . . . .56
How to Set up Restrictions Using the “TV guidelines” . . . . .56
How to Set up Restrictions using the MPAA Ratings:
G, PG, PG-13, R, NC-17, X . . . . . . . . . . . . . . . . . . . . . . . . . .58
How to Reset the TV after the V-Chip
Blocks a Channel (“Emergency Escape”) . . . . . . . . . . . . . . .59

Chapter 5: PC Display . . . . . . . . . . . . . . . . .60

Using Your TVas a Computer (PC) Display . . . . . . . . . . . . . . . . . . . . .60
How to Set up Your PC Software (Windows only) . . . . . . . .60
Adjusting the Screen Quality . . . . . . . . . . . . . . . . . . . . . . . . .61
Changing the Screen Position . . . . . . . . . . . . . . . . . . . . . . . . .62
To Initialize the Screen Settings . . . . . . . . . . . . . . . . . . . . . .63
How to DVI Select . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64
How to Auto Adjust . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65

Chapter 6: Troubleshooting . . . . . . . . . . . . .66

Identifying Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66

Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . .68

Installing Stand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68
Using the Anti-Theft Kensington Lock . . . . . . . . . . . . . . . . . . . . . . . . .69
How to Install the Wall Bracket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70
Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .72
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73
Display Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .74


CONTENTS 2


 venus-02-en 6/4/03 2:14 PM Page 1



Chapter One
YOUR NEW TV

List of Features

Your TV was designed with the latest technology. This TV is a high-performance unit
that includes the following special features:

• Easy-to-use remote control
• Easy-to-use on-screen menu system
• Automatic timer to turn the TV on and off
• Adjustable picture and sound settings that can be stored in the TV’s memory
• Automatic channel tuning for up to 181 channels
• A special filter to reduce or eliminate reception problems
• Fine tuning control for the sharpest picture possible
• A built-in multi-channel sound decoder for stereo and bilingual listening
• Equiped, dual channel speakers
• Headphone jack for private listening
• 16:9 letter box format available depending upon source
List of Parts

Please make sure the following items are included with your LCD TV. If any items are
missing, contact your dealer.


RF CABLE
(AA39-00039A)
Remote Control(BN59-00364B)
& Batteries (AAA x 2)
POWER CORD
(BH39-10339X)
Owner’s
Instructions
FRONT
SPEAKER
(BN96-00568C)
STAND
(BN96-00380A)
CORE(3301-001456)
x 5
English-1



 venus-02-en 6/3/03 3:04 PM Page 2



YOUR NEW TV

Familiarizing Yourself with The TV

Front Panel Buttons

The buttons on the front panel control your TV’s basic features, including the on-screen
menu. To use the more advanced features, you must use the remote control.


Power

Press to turn the TV on and off.

Power Indicator

Lights up when you turn the power off.

Remote Control Sensor

Aim the remote control towards this spot
on the TV.

TV/VIDEO


(See Page 17)
Displays a menu of all of the available
input sources (TV, VIDEO1, VIDEO2,
S-VIDEO, Component 1, Component 2,
PC/DVI).


MENU

Press to see an on-screen menu of
your TV’s features.

– VOL +
Press to increase or decrease the volume.
Also used to select items on the
on-screen menu.


CH
Press to change channels.
Also press to highlight various items
on the on-screen menu.
(Without the Remote Control, You can
turn on TV by using the Channel buttons.)


English-2



English-3
YOUR NEW TV
Rear Panel Jacks
Use the rear panel jacks to connect an A/V component that will be connected
continuously, such as a VCR or a DVD player.
For more information on connecting equipment, see pages 7-15.
VIDEO/AUDIO OUTPUT
VIDEO/AUDIO INPUT
SUPER VIDEO INPUT
HEADPHONE jack
COMPONENT
DIGITAL AUDIO IN jack
PC AUDIO INPUT
PC VIDEO(DVI-D) INPUT
SPEAKER OUT jack
WOOFER OUTPUT
RF INPUT
Kensington Lock
POWER INPUT
venus-02-en 6/3/03 3:04 PM Page 3

venus-02-en 6/3/03 3:04 PM Page 4


YOUR NEW TV

Remote Control

Frequently Used Buttons

You can use the remote control up to a distance of about 23 feet from the TV. When using the remote,
always point it directly at the TV.


POWER

Turns the TV on and off.
(See Page 16)

P.SIZE

Press to change the screen size.
(See Page 38)

P.MODE

Adjusts the TV picture by selecting
one of the preset factory settings.
(See Page 27)

MUTE

Press to temporarily cut off
the sound.
(See Page 17)


MENU

Displays the main on-screen menu.
(See Page 17)


LCD Screen

Shows the battery status and
selected input source device.
Shows the currently selected input
source.

Input Select Button

Use to select an input source - TV,
Set-top box (Digital Broadcast
Receiver), video, cable or DVD.
(See Page 18-20)

CH


and CH
(Channel Up/Down)
Press CH


or CH
to change
channels.(See Page16)
VOL +, VOL


Press to increase or decrease
the volume. (See Page 16)

TV/VIDEO

Press to display all of the available
video sources. (See Page 25-26)

JOYSTICK

Use to select on-screen menu
items and change menu values.
(The remote control will only
function with VCR or DVD units
that are compatible with the LCD TV.)

Video/DVD Control
Button

Use this button to control the video
or DVD functions.

• Works only with compatible VCR
or DVD players.
English-4



venus-02-en 6/3/03 3:04 PM Page 5


YOUR NEW TV


Convenient Buttons

+100

Press to select channels over 100.
For example, to select channel 121,
press “+100”, then press “2” and “1”.
(See Page 24)

Sleep Timer

Press to select a time for the TV to
turn off automatically.
(See Page 54)


Automatic Channel
Button

Press to automatically store
selected TV/cable channels.
(See Page 24)

ADD/ERASE

Press to add or erase channels
in the TV’s memory.
(See Page 25)

DNIe Button

Press to improve the digital video
quality. (See Page 40)

PC

Press to switch to the PC mode.

SET button


PRE-CH

Tunes to the previous channel.
(See Page 16)


Display Button

Press to display the current channel
and audio/video settings.
(See Page 17)

EXIT

Press the menu to exit.

PIP

See the PIP screen section of this
manual. (See Page 36)

STILL

Press to stop the action during
a particular scene. Press again to
resume normal video.
(See Page 38)


MTS Button

Press to select MONO or STEREO
mode. (See Page 47)

Dolby Digital Button

Press to enjoy theater-quality 3-D
sound. (See Page 41-45)


PIP controls

(See Page 37)

CH

Displays the available channels
in sequence.
(These buttons change channels
in the PIP window only.)


SIZE

Press to make the PIP window
double, large or small.


SWAP

Exchanges the video signal that is
currently displayed on the main
screen with the signal in the PIP
window.
(While the main screen is in
PC mode, it does not work.)

RESET

When your remote does not work,
change the batteries and press the
“Initialize” button for 2-3 seconds
before use.


English-5



 venus-02-en 6/3/03 3:04 PM Page 6



YOUR NEW TV

Installing Batteries in the Remote Control
1

Slide the cover out
completely.



Make sure to match the “+” and

2

“–” ends of the batteries with the

Install two AAA size

diagram inside the compartment.

batteries.


Remove the batteries and store them
3


in a cool, dry place if you won’t be

Replace the cover.

using the remote control for a long
time.

The remote control can be used
up to about 23 feet from the TV.

(Assuming typical TV usage,
the batteries last for about one year.)


The remote control doesn’t work!

Check the following:

1. Is the TV power switch on?
2. Is the selected source TV and not video, cable or DVD?
3. Are the plus end and the minus end of the battery reversed?
4. Did the battery run out?
5. Is there a power outage?
6. Is the power cord unplugged?
7. Is there a special fluorescent light or a neon sign nearby?
English-6



 venus-02-en 6/3/03 3:04 PM Page 7



Chapter Two
INSTALLATION

Connecting VHF and UHF Antennas

If your antenna has a set of leads that
look like this, see “Antennas with
300-ohm Flat Twin Leads”, below.


If your antenna has one lead that looks

like this, see “Antennas with 75-ohm
Round Leads”, on page 8.


If you have two antennas, see “Separate
VHF and UHF Antennas”, on page 8.

Antennas with 300-ohm Flat Twin Leads

If you are using an off-air antenna (such as a roof antenna or “rabbit ears”) that has
300-ohm twin flat leads, follow the directions below.

1


Place the wires from
the twin leads under
the screws on a 30075
ohm adaptor (not
supplied). Use a
screwdriver to tighten
the screws.


2

Plug the adaptor into
the TV ANTENNA
terminal on the
bottom of the back
panel.


English-7



 venus-02-en 6/3/03 3:04 PM Page 8



INSTALLATION

Antennas with 75-ohm Round Leads

1

Plug the antenna
lead into the TV
ANTENNA terminal
on the bottom of the
back panel.



Separate VHF and UHF Antennas

If you have two separate antennas for your TV (one VHF and one UHF), you must
combine the two antenna signals before connecting the antennas to the TV. This
procedure requires a an optional combiner-adaptor (available at most electronics shops).

1

Connect both antenna
leads to the combiner.


2

Plug the combiner
into the TV
ANTENNA terminal
on the bottom of
the rear panel.

Connecting Cable TV

To connect to a cable TV system, follow the instructions below.

Cable without a Cable Box

Because this TV is cable-ready,

you do not need a cable box to

1

view unscrambled cable channels.

Plug the incoming

cable into the TV
ANTENNA terminal
on back of the TV.


English-8



 venus-02-en 6/3/03 3:04 PM Page 9



INSTALLATION

Connecting to a Cable Box that Descrambles All Channels


This terminal might be labeled

1

“ANT OUT”, “VHF OUT”, or

simply, “OUT”.

Find the cable that is

connected to the
ANTENNA OUT
terminal on your cable
box.


2

Connect the other end
of this cable to the TV
ANTENNA terminal on
the back of the TV.



Connecting to a Cable Box that Descrambles Some Channels

If your cable box descrambles only some channels (such as premium channels), follow the
instructions below. You will need a two-way splitter, an RF (A/B) switch, and four lengths
of coaxial cable. (These items are available at most electronics stores.)


This terminal might be labeled

1

“ANT IN”, “VHF IN”, or simply,

Find and disconnect

“IN”.

the cable that is
connected to the
ANTENNA IN terminal
on your cable box.


2

Connect this cable
to a two-way splitter.



3

Connect a coaxial
cable between an
OUTPUT terminal on
the splitter and the IN
terminal on the cable
box.


English-9



English-10
4
Connect a coaxial
cable between the
ANTENNA OUT
terminal on the
cable box and the
B–IN terminal on the
A/B switch.
5
Connect another
cable between the
other OUT terminal
on the splitter and
the A–IN terminal on
the RF (A/B) switch.
6
Connect the last
coaxial cable
between the OUT
terminal on the RF
(A/B) switch and the
VHF/UHF terminal
on the rear of the
TV.
INSTALLATION
After you’ve made this connection, set the A/B switch to the “A” position for normal
viewing. Set the A/B switch to the “B” position to view scrambled channels.
(When you set the A/B switch to “B,” you will need to tune your TV to the cable box’s
output channel, which is usually channel 3 or 4.)
venus-02-en 6/3/03 3:04 PM Page 10

English-11
INSTALLATION
3
Connect a coaxial
cable between the
ANTENNA OUT
terminal on the VCR
and the antenna
terminal on the TV.
4
Connect a set of
audio cables
between the AUDIO
OUT jacks on the
VCR and the AUDIO
jacks on the TV.
5
Connect a video
cable between the
VIDEO OUT jack on
the VCR and the
VIDEO jack on the
TV.
Follow the instructions in “Viewing a VCR or Camcorder Tape” to view your VCR tape.
# Each external input source device has a different back panel configuration.
A coaxial cable is usually included with a VCR. (If not, check your local electronics store).
If you have a “mono” (non-stereo) VCR, use the Y-connector (not supplied) to hook up
to the left and right audio input jacks of the TV. If your VCR is stereo, you must connect
two cables.
Connecting a VCR
These instructions assume that you have already connected your TV to an antenna or a
cable TV system (according to the instructions on pages 7-10).
Skip step 1 if you have not yet connected to an antenna or a cable system.
1
Unplug the cable or
antenna from the
back of the TV.
2
Connect the cable or
antenna to the
ANTENNA IN terminal
on the back of the
VCR.
venus-02-en 6/3/03 3:04 PM Page 11

English-12
INSTALLATION
3
Connect an S-video
cable between the
S-VIDEO OUT jack on
the VCR and the
S-VIDEO INPUT jack
on the TV.
An S-video cable is usually included with an S-VHS VCR.
(If not, check your local electronics store.)
# Each external input source device has a different back panel configuration.
Make sure that the output is set to TV. (See Page 33)
# Each external input source device has a different back panel configuration.
1 To begin, follow
steps 1–3 in the
previous section to
connect the antenna
or cable to your
VCR and your TV.
Connecting an S-VHS VCR
Your Samsung TV can be connected to an S-Video signal from an S-VHS VCR.
(This connection delivers a better picture as compared to a standard VHS VCR.)
2
Connect a set of audio
cables between the
AUDIO OUT jacks on
the VCR and the
AUDIO INPUT jacks
on the TV.
1
Connect a set of
audio cables
between the AUDIO
IN jacks on the VCR
and the AUDIO
jacks on the TV.
2
Connect a video
cable between the
VIDEO IN jack on
the VCR and the
VIDEO jack on the
TV.
Connecting an External Input Source
Connect the Input/AUDIO cables to the Input/AUDIO OUT jacks on the TV and the
Input/AUDIO IN jacks on the VCR (Connect the cables to the jacks of the same color.)
venus-02-en 6/3/03 3:04 PM Page 12

English-13
INSTALLATION
Note: For an explanation of Component video, see your DVD player owner's manual.
# Each external input source device has a different back panel configuration.
Connecting a DVD Player
The rear panel jacks on your TV make it easy to connect a DVD player to your TV.
1
Connect a set of audio
cables between the
L, R AUDIO INPUT
jacks on the TV and
the AUDIO OUT jacks
on the DVD player.
2
Connect a video cable
between the
COMPONENT1 or
COMPONENT2
(Y, Pb, Pr) jacks on
the TV and the Y, Pb,
Pr jacks on the DVD
player.
Note: For an explanation of Component video, see your Set-Top Box owner's manual.
# Each external input source device has a different back panel configuration.
Connecting a Digital TV Set-Top Box
The connections for a typical set-top box are shown below.
1
Connect a set of audio
cables between the
L, R COMPONENT1
or COMPONENT2
AUDIO INPUT jacks
on the TV and the
AUDIO OUT jacks on
the Set-Top Box.
2
Connect a video cable
between the
COMPONENT1 or
COMPONENT2
(Y, Pb, Pr) jacks on
the TV and the Y, Pb,
Pr jacks on the
Set-Top Box.
venus-02-en 6/3/03 3:04 PM Page 13

English-14
INSTALLATION
Connecting the Speakers
5.1. Channel system: 5 channels – 2 channels for the front (left and right);
1 channel for the center; and 2 for the rear (left and right)
0.1 Channel – Subwoofer Channel
• The center, rear (left and right) and the subwoofer speakers are sold separately.
• Contact the nearest electronics store to purchase them.
1. Connect the speaker cables to the Speaker OUT jacks on the TV and the IN jacks on the speakers.
2. Connect the Subwoofer OUT jack on the TV to the subwoofer.
How to Connect
1. Turn the TV on and press the TV/Input button to select TV.
2. Press the Volume button to adjust the volume level.
How to Turn the Sound On
•Wind the speaker
cable on the core
twice or more.
1. Place the hooks on the
speaker and the TV set.
2. Tighten the screws to
secure the hooks.
venus-02-en 6/3/03 3:04 PM Page 14

English-15
INSTALLATION
Connecting a PC
Note: This figure shows the Standard Connector-jack panel. The actual configuration on
your TV may be different, depending on the model.
PC VIDEO CABLE
( DVI-D+DVI-D )
PC AUDIO CABLE
• PC AUDIO INPUT
Connect these to the audio-output jacks on your PC.
• PC VIDEO INPUT
Connect to the video output port on your PC.
# Each external input source device has a different back panel configuration.
TV rear panel PC rear
PC VIDEO CABLE
( DVI + D-SUB)
PC AUDIO CABLE
TV rear panel PC rear
DVI-D
D-SUB
venus-02-en 6/3/03 3:04 PM Page 15

 venus-03-en 6/3/03 3:05 PM Page 16



Chapter Three
SPECIAL FEATURES

Turning the TV On and Off

Press the POWER button.
You can also use the Power button on the front panel.


[Note]

1.
Use of the 'Power' button on the remote is possible only when the TV is
in 'Power Saving' (stand-by) mode. If the TV is powered off,
the remote cannot be used to turn the TV on.
2. To retain the time and or automatic alarm settings, always put the TV
in stand-by mode with the remote control.
Use of the the power switch on the TV will clear all time related settings.
[Benefit] This full 'power off' function is as effective as unplugging the power cable.

TV switches to stand-by mode when powered off by the remote control.

To return power (


) to the screen, press the remote control 'ON' or channel button
(
). Pressing the power button on the TV does not return power to the screen
because in this case, the TV restores the last mode, which was 'Power Saving'.
Changing Channels

Using the Channel Buttons

1

Press the CH


/
buttons to change channels.
When you press the CH


/
buttons, the TV changes channels in sequence.
You will see all the channels that the TV has memorized. (The TV must have
memorized at least three channels.) You will not see channels that were either erased
or not memorized.
Using the Pre-CH Button to select the Previous Channel

1

Press the PRE-CH button.
The TV will switch to the last channel viewed.


To quickly switch between two channels that are far apart, tune to one channel,
then use the number button to select the second channel. Then, use the PRE-CH
button to quickly alternate between them.

Adjusting the Volume

1

Press the VOL +/– buttons to increase or decrease the volume.


English-16



venus-03-en 6/3/03 3:05 PM Page 17


SPECIAL FEATURES

Using Mute

At any time, you can temporarily cut off the sound using the Mute button.


1

Press MUTE and the sound cuts off.
The word “


” will appear in the lower-left corner of the screen.
2

To turn mute off, press the MUTE button again, or simply
press either the VOL +/– button.

Viewing the Display

The display identifies the current channel and the status
of certain audio-video settings.

1

Press the Display
button on the remote
control.

The TV will display the
channel, the type of
sound, and the status


of certain picture and
sound settings.

Viewing the Menus
1

With the power on,
press the MENU button.

The main menu appears
on the screen. Its left
side has five icons:
Input, Picture, Sound,


Channel, Setup.

2

Use the UP/DOWN


buttons to select one of the
5 icons. Then press ENTER


or RIGHT
to access the
icon’s sub-menu.

3

Press the MENU button to exit.


The on-screen displays
disappear after about ten seconds.
Press the button once more or wait
approximately 10 seconds and it
disappears automatically.


Allows the user to adjust the
settings according to his/her prefer
ence and shows the current
settings.



The on-screen menus
disappear from the screen after
about thirty seconds.



You can also use the MENU,
CHANNEL, VOLUME and
TV/Video
buttons on the control
panel of the TV to make selections.
English-17



 venus-03-en 6/10/03 4:33 PM Page 18



SPECIAL FEATURES

Setting Up Your Remote Control

After it has been set up properly, your remote control can operate in four different modes:
TV, VCR, Cable, or DVD. Pressing the corresponding button on the remote control allows
you to switch between these modes, and control whichever piece of equipment you hoose.

Note
The remote control might not be compatible with all DVD Players, VCRs and Cable boxes.
Setting Up the Remote to Operate Your VCR
1 Turn off your VCR.


2 Press the MODE button and make sure that the VCR LED
is illuminated.

3 Press the Set button on your TV’s remote control.

4 Using the number buttons on your remote control, enter
three digits of the VCR code listed on page 21 of this
manual for your brand of VCR. Make sure you enter three
digits of the code, even if the first digit is a “0”.
(If more than one code is listed, try the first one.)

5 Press the Power button on the remote control. Your VCR
should turn on if your remote is set up correctly.

If your VCR does not turn on after set up, repeat steps
2, 3, and 4, but try one of the other codes listed for your
brand of VCR. If no other codes are listed, try each VCR
code, 000 through 089.


Note on Using Remote Control Modes: VCR
When your remote control is in “VCR” mode, the volume buttons still control your TV’s volume.


English-18



 venus-03-en 6/10/03 4:34 PM Page 19



Setting Up the Remote to Operate Your Cable Box

1 Turn off your cable box.


2 Press the MODE button and make sure that the Cable LED is
illuminated.

3 Press the SET button on your TV’s remote control.

4 Using the number buttons on your remote control, enter three
digits of the cable box code listed on page 21 of this manual
for your brand of cable box. Make sure you enter three digits
of the code, even if the first digit is a “0.”
If there is more than one code listed, try the first one.

5 Press the Power button on the remote control. Your cable box
should turn on if your remote is set up correctly.

If your cable box does not turn on after set up, repeat steps
2, 3, and 4, but try one of the other codes listed for your brand
of cable box. If no other codes are listed, try each code, 000
through 077.


Note on Using Remote Control Modes: Cable Box
When your remote control is in “Cable Box” mode, the volume buttons still control your TV’s volume.


English-19



 venus-03-en 6/10/03 4:34 PM Page 20



Setting Up the Remote to Operate
Setting Up the Remote to OperateSetting Up the Remote to Operate Y
YYour DVD
our DVDour DVD

1Turn off your DVD.


2 Press the MODE button and make sure that the DVD LED is
illuminated.

3 Press the SET button on your TV’s remote control.

4Using the number buttons on your remote control, enter three
digits of the DVD code listed on page 21 of this manual for
your brand of DVD. Make sure you enter three digits of the
code, even if the first digit is a “0.”
If there is more than one code listed, try the first one.

5 Press the Power button on the remote control. Your DVD should
turn on if your remote is set up correctly.

If your DVD does not turn on after set up, repeat steps 2, 3, and
4, but try one of the other codes listed for your brand of DVD.
If no other codes are list-ed, try each code, 000 through 008.


Note on Using Remote Control Modes: DVD
When your remote control is in “DVD” mode, the volume buttons still control your TV’s volume.


English-20



 venus-03-en 6/3/03 3:05 PM Page 21


Remote Control Codes
VCR Codes



Admiral
Aiwa
Audio Dynamics
Bell&Howell
Broksonic
Candle
Canon
Citizen
Colortyme
Craig
Curtis-Mathes
Daewoo
DBX
Dimensia
Dynatech
Electrohome
Emerson
Fisher
Funai
GE
Go Video
Harman Kardon
Hitach
Instant Replay
JC Penney
JCL
JVC
kenwood
015,088
024
022,025
011
019
016,018,022,054,055,061
017,062
016,018,022,054,055,061
023
016,021
009,016,017,023,024,055,062,073,076
003,004,005,006,007,008,022,054,085
009
024
036
017,018,019,022,024,029,032,036,043,
050,051,056,058,066,071,074,076,077,079
011,021,027,028,052,057,067
024
016
023
014,024,044,045
017
011,014,016,017,023,025,039,044,060,062
011,017,023,025,039,055
011,023,025,039,055
082
001,002,007
024
040
024
017,038,062,065
011,017,023,025,038,039,055,070
016,024
016,024,040,041
011,023,025,039,055,070,073
015
017,062,084,086
014,044
055
017,038,062,065
017,038
014,025,042,059
053,054,061
009
011
017,053
011,015,017,018,021,
024,028,036,052,062
KLH
LG
Lloyd
Logik
LXI
Magnavox
Marantz
Marta
MEI
Memorex
MGA
Midland
Minota
Mitsubishi
Montgomery ward
MTC
Multitech
NEC
Optimus
Panasonic
Pentax
Pentex Reserch+
Philco
Philips
Pioneer
Portland
ProScan
Quartz
Quasar
Radio Shack/Realistics
RCA
Samsung
Sansui
Sanyo
Scott
Sears
Sharp
Shintom
Signature
Sony
Sylvania
Symphonic
Tandy
Tashiko
Tatung
Teac
Technics
Temika
TMK
Toshiba
Totevision
Unitech
Vector Research
Victor
Video Concepts
Videosonic
Wards
Yamaha
Zenith
009,014,016,017,037,044,046,063,078
000,016,022,031,041,051
025
011,021
022,050,058,077
011,014,018,021,027,028,044,052,057
015,036,048,054
026,035,040,064
024
026,035,047
017,024,038,062,065
024
011,024
039
024,039,078
017
076
014,022,028,057,058
016,018
Cable Box Codes

015,016Anvision 017NSC 054Signature
015,016Cable star 024,046Oak 035Sprucer
015,016Eagle 024Osk Sigma 054Starcom
Eastrm Int. 011,035,047,069 Panasonic 066Stargate 2000
054General Instrument 015,016,027,029,034,036,037,040,041,048,049Philips 019,067Sylvania
012,013,023,031,032,GI 026,028,052Pioneer 019,067Texscan
033,038,044,075,076,077 015,016Randtek 025,029,057,058,063Tocom
011,012,020,021,042,056 Hamlin 008,035,074RCA 039,040,049Unika
045,051,054Hitachi 011,020,021 Regal 059,060Universal
012,013,023,031,032,033,038,044,054,070,073Jerrold 010,041Regency 015,016,027,029,034,036,037,040,041,048,049Viewstar
045,051Macom SA 052Warner Amex
015,016,027,029,034,036,037,040,041,048,049Magnavox 000,011,030,052,071,072 Samsung 022,050,065,069Zenith

DVD Codes

Philips 007
Proscan 008
RCA 008
Toshiba 002
Panasonic 006
Sony 004
Samsung 000

English-21



 venus-04-en 6/3/03 3:07 PM Page 22



Chapter Four
OPERATION
Plug & Play Feature

When the TV is initially powered On, two basic customer settings proceed
automatically and subsequently: Setting Auto program, Clock.

1

Press the POWER
button on the remote
control.


The message “Plug &
Play” is displayed.


2
Press the ENTER
button.
The TV will begin memorizing
all of the available
channels.
3

Press the LEFT/RIGHT
buttons to move
to the hour or minute.
Set the hour or minute
by pressing the
UP/DOWN


buttons.
(refer to “Setting and
Displaying the Current
Time” on page 51.)

4

The message
“Enjoy your watching.”
is displayed.



English-22



venus-04-en 6/3/03 3:07 PM Page 23


OPERATION

Memorizing the Channels

Your TV can memorize and store all of the available channels for both “off-air” (antenna)
and cable channels. After the available channels are memorized, use the CH


and CH
buttons to scan through the channels. This eliminates the need to change channels by
entering the channel digits. There are three steps for memorizing channels: selecting a
broadcast source, memorizing the channels (automatic) and adding and deleting channels
(manual).
Selecting the Video Signal-source

Before your television can begin memorizing the available channels, you must specify the
type of signal source that is connected to the TV (i.e., an antenna or a cable system).

1

Press the MENU button
to display the menu.
Press the DOWN
button to select
“Channel”, then press
the ENTER button.
2


Repeatedly press the

ENTER


button to
cycle through these
choices:
Air (antenna), STD,
HRC or IRC (all cable
TV).
Note : STD, HRC and IRC identify various types of cable
TV systems. Contact your local cable company to identify the
type of cable system that exists in your particular area.

At this point the signal source has been selected.
Proceed to “Storing Channels in Memory” (next page).

English-23



 venus-04-en 6/3/03 3:07 PM Page 24



OPERATION

Storing Channels in Memory

(Automatic Method)

1

First, select the correct
signal source (Air, STD,
HRC, IRC). See steps
1~2 on previous page.


Press the MENU
button.



Press the DOWN
button to select
“Channel”, then press
the ENTER



button.
2

Press the DOWN
button to select
“Auto program”.


3

Press the ENTER
button.
The TV will begin
memorizing all of the
available channels.


4


After all the available channels are stored, the Auto
program menu reappears. Press the MENU button to exit.

To select channels over 100,

Ex) Press


->
->
to select cable channel 108.
English-24


The TV automatically cycles
through all of the available
channels and stores them in

memory. This takes about one to
two minutes.
Press ENTER


at any time to
interrupt the memorization process
and return to the CHANNEL menu.

 venus-04-en 6/3/03 3:07 PM Page 25



OPERATION

Adding and Erasing Channels (Manual Method)

1

Use the number buttons to directly select the channel that will be added or
erased.

2

Press the ADD/ERASE button.
Repeatedly pressing this button will alternate between “Added” and “Erased.”


You can view any channel (including an erased channel) by using the number
buttons on the remote control.

To Select TV/Input

Use to select TV or other external input source connected to the TV.
Use to select the screen of your choice.

1


Press the MENU button
to display the on-
screen menu.

press the ENTER
button.


2


Press the ENTER
button to select
“TV”, then press the
ENTER button.
English-25



 venus-04-en 6/3/03 3:07 PM Page 26



OPERATION

To Edit the Input Source Name

Name the input device connected to the input jacks to make your input source selection easier.

1


Press the MENU button
to display the on-
screen menu.
Press the DOWN
button to select “Input”,
then press the
ENTER button.
2

Press the DOWN
buttons to select
“Edit Name”, then
press the ENTER
button.


3

Press the UP/DOWN
buttons repeatedly until
the correct vcr appears.


After the vcr is entered,
press the ENTER
button.


English-26



 venus-04-en 6/3/03 3:07 PM Page 27



OPERATION

Using Automatic Picture Settings

Your TV has two automatic picture settings (“Custom”, “Dynamic”, “Standard”, and
“Movie”) that are preset at the factory. You can activate either Custom, Dynamic,
Standard, or Movie by pressing P.MODE (or by making a selection from the menu). Or,
you can select “Custom” which automatically recalls your personalized picture settings.

1

Press the MENU button
to display the menu.

Press the DOWN
button to select
“Picture”, then press
the ENTER
button.


2


Press the

UP/DOWN


buttons to select the
“Dynamic”, “Standard”,
“Movie” or “Custom”
picture setting.


Alternate method:

Simply press the P.MODE button on the remote
control to select one of the standard picture settings.



Choose Dynamic to increase the clarity and sharpness of the picture.

Choose Standard for the standard factory settings.

Choose Movie when viewing the movies.

Choose Custom if you want to adjust the settings accordings to personal
preference (see “Customizing the Picture, page 28).
English-27



 venus-04-en 6/3/03 3:07 PM Page 28



OPERATION

Customizing the Picture

You can use the on-screen menus to change the contrast, brightness, sharpness,
color and tint according to personal preference.
(Alternatively, you can use one of the “automatic” settings. See before page.)



1

Press the MENU button
to display the menu.

Press the DOWN
button to select
“Picture”, then press
the ENTER


button.
2

Press the

ENTER


buttons to select a
particular item.

3

Press the

LEFT/RIGHT


buttons to increase or
decrease the value of
a particular item.
For example, if you
select “Contrast”,
pressing RIGHT
increases it.


Press the MENU button
to exit.


The customer can select Color Tone:
“Cool 2”, “Cool 1”, “Normal”,
“Warm 1”, “Warm 2” according to
personal preference.


English-28



 venus-04-en 6/3/03 3:07 PM Page 29



OPERATION

Using Automatic Sound Settings

Your TV has four automatic sound settings (“Custom”, “Standard”, “Music”, “Movie” and
“Speech”) that are preset at the factory. You can activate any of them by pressing the
S.MODE button (or by making a selection from the on-screen menu). Or, you can select
“Equalizer”, which automatically recalls your personalized sound settings.

1
Press the MENU button
to display the menu.
Press the DOWN
button to select
“Sound”, then press the
ENTER button.
2


Press the ENTER
button. Press the


UP/DOWN


buttons repeatedly to
select the “Standard”,
“Music”, “Movie”,
“Speech” or “Custom”

sound settings.


Alternate method:
Simply press the the S.MODE button on the remote
control to select one of the standard sound settings.


• Choose Standard for the standard factory settings.
• Choose Music when watching music videos or concerts.
• Choose Movie when watching movies.
• Choose Speech when watching a show that is mostly dialogue (i.e., news).
• Choose Custom to recall your personalized settings.
English-29



 venus-04-en 6/3/03 3:07 PM Page 30



OPERATION

Customizing the Sound

The sound settings can be adjusted to suit your personal preference.
(Alternatively, you can use one of the “automatic” settings. See before page.)

Press the MENU button
to display the menu.
Press the DOWN
button to select
“Sound”, then press the
ENTER button.
1

2

Press the DOWN
button to select
“Custom Sound”, then
press the ENTER
button.


3

Press the

UP/DOWN


buttons to select a
particular item to be
changed.

Press the

LEFT/RIGHT


buttons to increase or
decrease the value of a
particular item.

Press the MENU button
to exit.


English-30



 venus-04-en 6/3/03 3:07 PM Page 31



OPERATION

Selecting a Menu Language

1


Press the MENU button
to display the menu.
Press the DOWN
button to select
“Setup”, then press the
ENTER button.
2

Press the DOWN
button to select
Language.


Press the ENTER
button.


3

Press the DOWN
button to select
“English”, “Français”,
“Español” or
“Português”.


Press the ENTER
button.




Comments
Search
Only registered users can write comments!

3.26 Copyright (C) 2008 Compojoom.com / Copyright (C) 2007 Alain Georgette / Copyright (C) 2006 Frantisek Hliva. All rights reserved."

 
 
Buy LCD
 


Copyright © 2017 BestBuyLCD. All Rights Reserved. Design by Arte-Web.it